Sunlite ST40Y48M10X6- Instrukcja Użytkownika Pobierz pdf

Model Max Input Voltage (Vdc) Max current (a) Max Wattage

ST40 48 3.5 66

Important Safety InStructIonS - Save theSe InStructIonS

uSe only wIth claSS 2 power unIt

• These products are only suitable for connection to a Class 2 power source

and have not been evaluated for use when connected to a power source

that does not comply with Class 2 voltage and energy limited supplies.

cautIon - to prevent the rISk of fIre, do not InStall In

a compartment Smaller than 10 IncheS by 10 IncheS by

(xx+12) IncheS (where xx IS the length of the lumInaIre In

IncheS)

all InStallatIonS of SunStrIp40 Should be

performed by a certIfIed electrIcIan and be In

complIance wIth the natIonal electrIcIanS code aS well

aS local codeS.

SuItable for wet locatIonS

E338721

Fixture Wiring:

Solid State led

St40

Strip light

Magnetic Mount

ertiFiCation:

UL and cUL

Damp/Wet Location Listed

IP64/IP66 Rated

energy:

>0.9 Power Factor

700-1400mA / ~ 48VDC

-30° C to 40°C

ContaCt:

4811 Quail Crest Place

Lawrence, KS 66049

www.sunlitest.com

T:785.856.0219

Fixture inStallation inStruCtionS:

SunStrip40 - “St40-” - low voltage claSS 2 led luMinaire

Suggested wiring utilizes bullet connections in alignment with the direction of current ow from the driver.

turn power off before any inStallation, inSpection or reMoval of fixture/wiring.

Strip Driver

W (-)

W (+)

B (-)

R (+)

Side with clip is positive.

Cut 1-1/8” hole in ceiling.

Drill 1-1/16” hole in ceiling. Hole location should be

near where the xture wires will be once mounted on

ceiling.

Retrieve wires in ceiling and outt with bullet

connections.

• Side of wire closer to LED driver should be tted with

a female bullet connector.

• Side of the wire farther from the LED driver should be

tted with a male bullet connector.

Outt xture wire with bullet connections.

• Core (+) with a male bullet connector.

• Shield (-) with a female bullet connector.

1 2 3

Connect xture wires and ceiling wires together (See

Fixture Wiring Diagram). Hide wires in ceiling and place

xture in desired location. Fixture should automatically

connect to the metal on the ceiling.

conSigneS de SÉcuritÉ iMportanteS - conServeZ SoigneuSeMent ceS inStructionS

a utiliSer uniQueMent avec une Source d’aliMentation de

claSSe 2

• Ces produits doivent être branchés uniquement à une source d’alimen-

tation de classe 2 et n’ont pas été testés pour une utilisation lors d’une

connexion à une source d’énergie non conforme à la tension de classe 2

et à l’approvisionnement en énergie limitées.

attention - pour Éviter leS riSQueS d’incendie, ne paS

inStaller danS un coMpartiMent inferieur a 10 pouceS

Sur 10 pouceS Sur (xx+12) pouceS (oÙ xx eSt la longueur

du luMinaire en pouceS).

ce produit doit Étre inStallÉ Selon le code

d’inStallation pertinent, par une perSonne Qui connaÍt

bien le produit et Son fonctionneMent ainSi Que leS

riSQueS inhÉrentS.

convient aux eMplaceMentS MouillÉS.

1 2

Podsumowanie treści

Strona 1 - Fixture Wiring:

Model Max Input Voltage (Vdc) Max current (a) Max WattageST40 48 3.5 66Important Safety InStructIonS - Save theSe InStructIonSuSe only wIth claSS 2 po

Strona 2 - DriVer recommenDationS:

www.SunliteSt.com 4811 Quail creSt Place t: 785.856.0219connect lawrence, KS 66049 08/19/14Solid State ledST40Strip lightMagnetic MountDimming Wiring

Więcej dokumentów dla Urządzenia optyczne Sunlite ST40Y48M10X6-

Aby wyświetlić dokument Sunlite ST40Y48M10X6- Instrukcja Użytkownika

Sunlite ST40Y48M10X6- Instrukcja Użytkownika (2 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Sunlite ST40Y48M10X6- Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Urządzenia optyczne Sunlite ST40Y48M10X6-. Sunlite ST40Y48M10X6- Manuel d'utilisation Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Urządzenia optyczne Sunlite ST40Y48M10X6-

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Urządzenia optyczne Sunlite ST40Y48M10X6-